Free shipping on orders overFree shipping over $250 Lower 48 states and DC. Excludes freight and oversize.

Hones

Displaying 1 to 12 (of 12 products)
(image for) 1/2" Flex Hone 120 Grit Tool
1/2" Flex Hone 120 Grit Tool
Brush Research BC1212
Your Price: $14.29
(image for) 16mm Flex Hone
16mm Flex Hone
CTA Manufacturing Corp. 2268
Your Price: $30.00
(image for) 180G 3/4 Flex Hone
180G 3/4 Flex Hone
Brush Research BC3418
Your Price: $18.10
(image for) 5/8" Flex Hone 180 Grit
5/8" Flex Hone 180 Grit
Brush Research BC5818
Your Price: $16.07
(image for) BC 8MM .315" 180SC FLEX HONE
BC 8MM .315" 180SC FLEX HONE
Brush Research BC8M18
Your Price: $13.63
(image for) BC 9.5MM 400SC .357MAG 1-5/8 AP 3
BC 9.5MM 400SC .357MAG 1-5/8 AP 3
Brush Research 00899
Your Price: $20.66
(image for) BMC 25 .008 MANDREL MOUNTED
BMC 25 .008 MANDREL MOUNTED
Brush Research BMC2508
Your Price: $12.59
(image for) FLEX HONE 4 1/8' STD DUTY ENG
FLEX HONE 4 1/8' STD DUTY ENG
Brush Research GB41812
Your Price: $47.24
(image for) FLEX-HONE FOR ROTORS 240Z #152
FLEX-HONE FOR ROTORS 240Z #152
Brush Research RMFH240Z25
Your Price: $45.18
(image for) GB 3 1/4" 83MM 240SC FLEX HONE
GB 3 1/4" 83MM 240SC FLEX HONE
Brush Research GB31424
Your Price: $41.03
(image for) HONE RPLCMNT SET-FINE GRIT*NLA
HONE RPLCMNT SET-FINE GRIT*NLA
Old Forge Tools 7132-1
Your Price: $4.17
(image for) HONE RPLCMNT SET-FINE GRIT*NLA
HONE RPLCMNT SET-FINE GRIT*NLA
Old Forge Tools 7132-3
Your Price: $6.03
Displaying 1 to 12 (of 12 products)

Flex Hones and Cylinder Hones

A hone is an abrasive tool turned in a drill to finish the inside of a bore. The flexible hones in this category, often called ball hones, carry small abrasive globules on flexible filaments. Because the filaments flex, the hone follows the existing bore instead of cutting a new one, and it leaves an even crosshatch finish.

How they are used

The most common job is deglazing an engine cylinder before new rings go in, so the rings can seat. Flex hones also remove light scoring, rust and varnish and deburr cross-drilled holes and ports. In use, the hone is lubricated with honing oil, spun in a drill and stroked in and out of the bore at a steady pace; the stroke speed sets the crosshatch angle. The bore is then cleaned thoroughly to remove abrasive and metal particles.

Choosing size and grit

Flex hones are sized to the bore diameter, in inch and metric sizes, and the hone should be slightly larger than the bore so the filaments press on the wall. Grit sets the finish: coarser grits remove more material, finer grits leave a smoother surface. Engine rebuilders, machine shops, auto repair technicians and industrial maintenance shops use them on engine, compressor and hydraulic cylinders. Grinding stones, burrs and wire brushes are in nearby Abrasives and Grinding categories.

Brands we carry here include Brush Research, Old Forge and CTA.