What are the advantages of using a suction feed HVLP spray gun?

Suction feed HVLP (High Volume Low Pressure) spray guns offer several advantages. They tend to be more versatile for spraying in different orientations compared to gravity feed guns, as the cup's position is less critical. The initial cost is often lower, making them a good entry point for those new to HVLP spraying. Plus, changing colors can be slightly faster since you're dealing with a smaller amount of material in the cup. Models like the DeVilbiss JGA-670 Plus are known for their balance and feel.

What kind of materials can I spray with a suction feed HVLP gun?

Suction feed HVLP spray guns are versatile and can handle a wide range of coatings. This includes primers, base coats, clear coats, lacquers, enamels, and even some thicker materials like latex paint (though thinning might be required). The key is to select the correct fluid tip size for the viscosity of the material. Always check the manufacturer's recommendations for your specific gun and coating to ensure proper atomization and prevent clogging. For example, the DeVilbiss GTI-620S comes with multiple tips to handle different materials.

How do I properly clean and maintain my suction feed HVLP spray gun?

Proper cleaning is crucial for maintaining the performance and lifespan of your suction feed HVLP gun. Immediately after use, empty any remaining material from the cup. Then, flush the gun with the appropriate solvent for the coating you were using. Disassemble the gun, clean all parts (including the fluid tip, air cap, and needle) with brushes and solvent, and ensure all passages are clear. Lubricate moving parts as recommended by the manufacturer. Regularly inspect and replace worn parts like gaskets and O-rings, such as the DeVilbiss TGC-9-K5 lid gasket, to prevent leaks.

What factors should I consider when choosing a fluid tip size for my suction feed HVLP gun?

The viscosity of the material you're spraying is the primary factor in determining the correct fluid tip size. Thicker materials require larger tips, while thinner materials need smaller ones. The manufacturer's recommendations for your specific gun and coating should be your guide. If you're unsure, start with a smaller tip and gradually increase the size until you achieve proper atomization without excessive material buildup. Consider the DeVilbiss JGA series, which offers a range of fluid tips for various applications.

How does a suction feed HVLP gun work compared to other types of spray guns?

Suction feed HVLP guns use a vacuum created by the compressed air flowing through the air cap to draw the coating material up from the cup below. This differs from gravity feed guns, where gravity assists the material flow, and pressure feed guns, where the material is forced into the gun under pressure. Suction feed guns are generally less efficient than gravity feed in terms of material usage, but they offer good versatility and are often more affordable. They are suitable for a wide range of projects where high transfer efficiency isn't the top priority.

What is the purpose of a drip-free valve on a suction feed HVLP gun?

A drip-free valve, like the DeVilbiss TGC-407-1-K3, is designed to prevent paint from dripping or leaking from the fluid tip when the gun is not actively spraying. This helps to reduce material waste, keep your work area cleaner, and prevent imperfections in your finish. These valves are especially useful when working on intricate or detailed projects where precise control is essential. They contribute to a more professional and efficient spraying experience.

What air pressure is recommended for suction feed HVLP spray guns?

HVLP (High Volume Low Pressure) spray guns are designed to operate at lower air pressures compared to conventional spray guns. While specific pressure settings vary by model and manufacturer, most suction feed HVLP guns operate in the range of 20-35 PSI at the air cap. Always refer to the manufacturer's recommendations for your specific gun to ensure optimal atomization and transfer efficiency. Using excessive air pressure can lead to paint bounce-back, overspray, and reduced coating quality.

Can I use a disposable cup liner with my suction feed HVLP gun?

While disposable cup liners are more commonly used with gravity feed spray guns, they can sometimes be adapted for use with suction feed cups. However, it's crucial to ensure the liner fits securely and doesn't interfere with the suction mechanism or the gun's operation. Check the liner manufacturer's specifications for compatibility with your specific gun model. In many cases, thorough cleaning of the standard cup is preferred over using liners with suction feed systems.

Search

Manufacturers [more]

DeVilbiss | 190391 | TGC-9-K5 Tri Seal Lid Gasket 5/Pk

Name: TGC-9-K5 Tri Seal Lid Gasket 5/Pk
Brand: DeVilbiss
SKU: 126341
Price: 43.2 USD
Availability: InStock
Rating: 3 (1 reviews)

larger image

DeVilbiss 190391 TGC-9-K5 Tri Seal Lid Gasket 5 Pack

Other products
DeVilbiss Homepage
Model: 126341
Shipping Weight: 1lbs
Manufacturers Part #: 190391
Manufactured by: DeVilbiss
Also Known As: DV190391, DEVTGC-9-K5

Only 3 left in stock - order soon

Add to cart for details

Add to Cart:

Earn 1% Back On Every Purchase (Rewards Program)

We are Here To Help (Contact Us)

Write Review

This product was added to our catalog on Thursday 15 September, 2011.

Automatic Discount

Special Deal: Purchase the item above and the one below to save!

Old Price:

$83.2000

- $6.48

Your Price:

$76.72

Search

Manufacturers [more]

Categories

DeVilbiss | 190391 | TGC-9-K5 Tri Seal Lid Gasket 5/Pk

Add to cart for details

Automatic Discount

Special Deal: Purchase the item above and the one below to save!

Related Products

Customers who bought this product also purchased...

Customers Also Shopped For

Customer Service

Popular Manufacturers

Popular Categories