Subcategories
Best Sellers For Drive Train- Transmission
-
Input Shaft Seal Installer J37073
Manufacturers Part #: J-37073
Your Price: $41.56Automotive Specialty Tools TRW Steering Gear Input Shaft Seal Driver OTC Kent-Moore J37073 Input Shaft Seal Installer ... -
Jiffy-tite Quick Disconnect Tool - 3/8 Inch
Manufacturers Part #: JT38LP
Your Price: $24.50100% Made in USA! The 3/8" Jiffy-tite(R) Quick Connect fitting is currently the most widely used quick connect fitting used in the marketplace. The 3/8" fittings are found on all 1996 and newer General Motors transmissions. The radiator end of the transmission oil cooling line houses many Jiffy-tite(R) 3/8" Quick Connect fittings as well. These are also used on many DCX applications. Reasons to use a Jiffy-tite disconnect tool: Tool enables much ... -
Flywheel Holding Tool
Manufacturers Part #: J-42386-A
Your Price: $126.94Includes Free ShippingApplications: GEN 3 ENGINE, C/K, F, Y CAR J 42386-A is designed to hold the engine stationary while the damper bolt is being torque. This item may not be in stock; please email service@toolsource.com for cost and lead time before ordering. Kent-Moore J-42386-A Flywheel Holding Tool ... -
Mercedes 722.9 Drive Line Filler Adapter ATF 129
Manufacturers Part #: ATF129
12mm x 1.5 Mercedes-Benz adapter for the 722.9 Automatic Transmissions.Used in conjunction with the ATF Filler System.Individual adapter included (does not include pump, container, hose, or shut-off valve).Made in the U.S.A. Applicable to the following chassis with the 722.9 Transmission: 164, 171, 203, 204, 209, 211, 215, 216, 219, 220, 221, 230, and 251. Assenmacher ATF 129 Mercedes "722.9" Drive Line Filler Adapter ... -
Axle Seal Installer
Manufacturers Part #: 5041
Your Price: $94.95Use this tool to install front axle seals into Dana #44 and 60 disconnect axles to their proper depth. Also used with Miller P/N 8411, 8415, 8416 and 8834. 1988 thru 2002.Replacement parts include 5041-1 Installer, 5041-2 Forcing Screw and 5041-3 Disc, also available separately. Manufacturer drop ship; please email service@toolsource.com for lead time. SPX Miller Special Tools Mopar 5041 Axle Seal Installer ... -
Transmission Fluid Fill Adapter 307-437
Manufacturers Part #: 6604
Your Price: $12.93This is a required tool to fill or add fluid to the 5R55W automatic transmission used on 2003 - newer Ford Explorers. Same as Ford No. 307-437. Operating instructions: remove fill plug from transmission: install No.OTC 6604: fill transmission to correct fluid level: remove No. OTC 6604: and reinstall fill plug in transmission. OTC 6604 Transmission Fluid Fill Adapter ... -
Transmission Oil Cooler Line Disconnect Tool Set - Ford, Cadilla
Manufacturers Part #: 39960
Your Price: $7.02Two sizes, 3/8" and 1/2", are designed to disconnect transmission cooler lines.Use 3/8" size for 2003 and later Ford V8 Explorer, 2004 and later Ford F150 and Cadillac CS.Use 1/2" size for Ford Super Duty Trucks, F250, F350 and F450.Tip is specially stepped to fit connector.Simply push the line toward the connector, then engage tool and pull line from conector.Set comes skin packed.Shipping weight: 1 oz. Lisle 39960 2-Pc Transmission Oil Cooler ... -
VW/Audi DSG Drive Line Filler Adapter
Manufacturers Part #: ATF16DSG
VW/Audi DSG Drive Line Adapter used with the AST ATF Filler System.The attachment has a 24mm x 1.5 thread.Fits DSG Transmissions.24mm x 1.5 Assenmacher ATF16DSG VW/Audi "DSG" Drive Line Filler Adapter ... -
VW/Audi Drive Line Filler Adapter
Manufacturers Part #: ATF105
10mm x 1.0 VW/Audi Adapter used in conjunction with the ATF Series Filler PumpsComparable to VW tool # VAS 6262/2Individual adapter included (does not include pump, container, hose, or shut-off valve).For the complete VW/Audi Kit, see tool# ATF 1033 VW or ATF 1033-5 VW....
Featured Products - Drive Train- Transmission
-
Bushing Remover Bit
Manufacturers Part #: 91100
Your Price: $9.77Bushing Remover Bit Heavy Duty .401 Parker Shank Tool. Especially designed to remove bushing in control arm work. ... -
Halfshaft Remover / Differential Rotator (Escort / Lynx)
Manufacturers Part #: 7140
Your Price: $39.94No. 7140 is essential when removing the left-hand halfshaft from Escort/Lynx transaxles.Weight: 1lb., 13oz. OTC 7140 Escort/Lynx Halfshaft Remover/Differential Rotator ... -
Four Wheel Drive Ball Joint Service Kit
Manufacturers Part #: 7704
Your Price: $63.12This kit is used with ball joint service kit No. 7249 to remove and install upper and lower ball joints on 1967-current 1/2- and 3/4-ton 4WD vehicles having the Dana 44 front axle (found on Ford, GM, Dodge, IHC, and Jeep vehicles). >Wt., 2 lbs., 5 oz. OTC 7704 Four Wheel Ball Joint Service Kit ... -
Driver Tool Basic Set
Manufacturers Part #: 27794
Your Price: $355.14Includes Free ShippingAssemble your own custom made driver tools.Have the proper size driver for any seal, bearing, or bushing installing job.Set includes discs & handles you assemble to provide a pilot (to prevent cocking), a spacer (so force is applied on the proper area), & a driver (for even force distribution).Includes 41 discs & two handles.Size range: 1/2" thru 3" diameter.Packed in a plastic box w/ pre-cut tool tray.Weight: 22 lbs. 13 oz. Image is representat... -
Clutch Adjustment Two Gauge Set
Manufacturers Part #: 5035
Your Price: $61.41OTC 5035 Features: This two gauge set ensures correct adjustment for proper clutch operation on manual & self-adjusting, pull type, heavy duty clutches.The free play gauge checks the 1/8" clutch pedal free play between the yoke & bearing wear pad.The release bearing travel gauge verifies the 1/2" release travel between the release bearing & the transmission bearing cap.Weight: 1 lb. 8 oz. OTC 5035 Clutch Adjustment Two Gauge Set ... -
7019 Heavy Duty Seal Puller OF 206
Manufacturers Part #: 37019
Your Price: $15.39Remove the most stubborn seals from transmissions, axles and those seals that are difficult to reach, with this heavy-duty seal puller. This seal puller does the job. The finish is black oxide.1/2" x 12-1/2" Old Forge Tools 37019 Seal Puller ... -
Clutch Plate Remover - Coarse Thread
Manufacturers Part #: 90454
Your Price: $9.00Harrison A6 GMHarrison R-4 GM Non-stock item; please email service@toolsource.com for cost and lead time. Mastercool 90454 Coarse Thread Clutch Plate Remover ... -
GM Transmission Holding Fixture w/ Base
Manufacturers Part #: T-0156-B
Your Price: $288.59Includes Free ShippingGM Transmission Holding Fixture Complete With Base. Swings full 360 degrees.Locks at 90 degree increments.All steel construction.Allows work comfort at any angle.Also, allows easy access to work on valve body.Comes complete with base.For holding fixture without base, order T-0156BF. For:Turbo-hydramatic - 200/200C/200-4R.Turbo-hydramatic - 250/350/350C.Turbo-hydramatic - 375/400(3L80)/425/475.... -
Turbine Shaft Teflon Seal Installer/Resizer
Manufacturers Part #: T-1574
Your Price: $155.24Includes Free ShippingNon-stock item, manufacturer drop ship; please email service@toolsource.com for cost and lead time before ordering. This is a non-quoted item and the price fluctuates; we have to get pricing each time an order is placed. Prevents distortion during installations.One tool will set all four rings.Installs and resizes.Complete with instructions.New see-thru resizer prevents improper seal installation.For 4L60 only. Atec Trans-Tool T-1574 Turbine Sha...
Recently Added Products In Drive Train- Transmission
-
Bushing - Thru 1-1/2" - Part
Manufacturers Part #: 34200
Your Price: $30.25OTC Tools 34199 Bushing - Thru 1-1/2" - Part ... -
Differential Output, Seal Protector
Manufacturers Part #: 9099
Your Price: $7.45This special tool must be used to prevent damage to the Rear Differential Output Shaft Seals while removing or installing the axle shafts in Pacifica Vechicles Current Usage* 2006 (CS, LX) - System (3 - Differential and Driveline) 2007 (CS, JS, LX, MK, PM) - System (3 - Differential and Driveline) 2008 (CS, JS, LC, LX, MK, PM) - System (3 - Differential and Driveline) 2009 (JC, LC, LX, MK, PM) - System (3 - Differential and Drive... -
Kent Moore DT-47778-2 Pusher
Manufacturers Part #: DT-47778-2
Your Price: $166.24Includes Free ShippingKent-Moore DT-47778-2 Pusher For GM / General Motors.. ... -
Transmission Fluid Pump Alignment Gauge T74P-77103-C
Manufacturers Part #: 307-042
Your Price: $109.07Includes Free ShippingSame as Ford part number T74P-77103-CPart of 307-S035 and 307-S039Applications: A4LD OTC 307-042 Transmission Fluid Pump Alignment Gauge ... -
Transmission Linkage Bushing Installer
Manufacturers Part #: 909
Your Price: $32.86Transmission Linkage Bushing Installer 909 For Mercedes-Benz with automatic transmissions, all years, some Ford models and others. This tool will easily and safely push tough nylon bushings into place. Works on different bushing sizes. Save yourself headaches & time with this innovative tool from V8 Tools. V8 Tools 909 Transmission Linkage Bushing Installer ... -
Truck Clutch Alignment Shaft 1-1/2 Inch OD 1 Inch Pilot Ford D79
Manufacturers Part #: 308-D001
Your Price: $45.63Ford D79T-7550-A Universal1-1/2" OD 1" Pilot 10 Spline OTC 308-D001 Truck Clutch Alignment Shaft ... -
Ford Clutch Coupling Tool
Manufacturers Part #: 7646A
Your Price: $33.32Disconnects the hydraulic clutch line from the clutch slave cylinder on the following vehicles with manual transmissions and hydraulic clutches: 1988-newer F-series trucks, Bronco II, Ranger, Explorer, and 1989-1997 Ford Thunderbird and Mercury Cougar.Wedge-shaped design allows easy removal of clutch line without damaging clutch line, coupling, or slave cylinder. No need to pry the coupler apart. Ford Clutch Coupling Tool ... -
CV Boot Clamp Pliers for Earless Type Clamps
Manufacturers Part #: 30500
Your Price: $16.36A sturdy, low-cost tool.Works on earless type clamps including those found on GM inboard CV joints.Skin packed.Shipping weight 12 oz. Lisle 30500 CV Boot Clamp Pliers for Earless Type Clamps ... -
Back Pressure Tester
Manufacturers Part #: BPT02
Your Price: $71.60Quickly test back pressure and clogged or obstructed catalytic converters. Three stage Oxygen Sensor Port Adapter has 12MM and 18MM thread sizes to fit most domestic and import vehicles. The standard 1/4"-20 tip provides the ability to test through the exhaust pipe when O2 sensor ports are inaccessible.* High temperature silicon hose prevents damage to tester from high exhaust temperatures. * Pipe tap set not included. Easy to install 3 stage ada...