Shopping Cart 0 items
Your cart is empty.
  • Serving over 30 Million Customers
Your Professional Tools Authority

Automotive Specialty Tools > Engine Repair > Cylinder Tools > Sleeve Pullers > z-dup Output Shaft Sleve Remov

z-dup Output Shaft Sleve Remover

z-dup Output Shaft Sleve Remover
Output Shaft Sleve Remover J-41227

Tool Number: J-41227
Tool Name: OUTPUT SHAFT SLEEVE REMOVER
Applications: 4T40E

4T40E, 4T65E J-41227 is a two leg puller designed to locate behind the back lip of the sleeve for removal. This tool is required due to the limited access to the axle sleeve. The sleeve must be replaced when servicing the axle seals.


Kent- Moore KM J-41227 Output Shaft Sleve Remover
  • Shipping Weight: 2lbs
  • Manufactured by: Kent-Moore
  • Toolsource #: 111882
  • Manufacturers Part #: J-41227
  • Also Known As: KMJ41227

Usually In Stock
Usually ships in 24-48 hours
Manufacturer Direct

$221.48

Related Products

  • Ford Four Wheel Drive Caster/Camber Sleeve Puller D93T-3000-A
    Ford Four Wheel Drive Caster/Camber Sleeve Puller D93T-3000-A
    Manufacturers Part #: 7588A
    Your Price: $238.36Includes Free Shipping
    Removes rusted and seized bushings before resetting the caster/camber, and easily pulls most aftermarket and OE bushings on Ford 4WD vehicles.It`s the only tool available that works on any angle OE bushing, removing them quickly and without breaking the ears off.Applications: 1980-current full- size E- and F-series vans and pickups, and Broncos; 1983-89 Ranger and Bronco 11.Two horseshoe adapters are included to pull most aftermarket bushings wi...
  • Installing Conversion Kit for Sleeve Puller Set
    Installing Conversion Kit for Sleeve Puller Set
    Manufacturers Part #: 1201
    Your Price: $352.81Includes Free Shipping
    Permits the OTC No. 1200 sleeve puller to handle both removing & installing operations.Use OTC plate Nos. 1253-1256 for installing, & OTC plate Nos. 1219-1250 for removing.Plates are not included w/ kit.Includes screw ext., installing bar, & yoke assembly.Weight: 17 lbs. 13 oz. Kit Includes: OTC No. 33769 - Screw extension.OTC No. 41291 - Installing bar.OTC No. 302340 - Yoke assembly. OTC 1201 Installing Conversion Kit for Sleeve Puller Set ...
  • Head Handler - 6mm x 1.0
    Head Handler - 6mm x 1.0
    Manufacturers Part #: 66110
    Your Price: $22.56
    This unique tool allows the technician to easily lift and maneuver cylinder heads when service is needed. First, free the cylinder head from the block then choose the appropriate thread size. Then used in tandem, simply spin the Head Handler™ into each end of the cylinder head until snug. (use your descretion for strongest hold location). Now you can easily lift and carry the head. No more cut fingers from sharp edges or oil and coolant stai...
  • Head Handler Set 1/4 In x 20
    Head Handler Set 1/4 In x 20
    Manufacturers Part #: 66120
    Your Price: $21.39
    Head Handler Set 1/4" x 20 This unique tool allows the technician to easily lift and maneuver cylinder heads when service is needed. First, free the cylinder head from the block then choose the appropriate thread size. Then used in tandem, simply spin the Head HandlerT into each end of the cylinder head until snug (use your descretion for strongest hold location). Now you can easily lift and carry the head. No more cut fingers from sharp edges o...
  • Head Handler Set 8mm x 1.25
    Head Handler Set 8mm x 1.25
    Manufacturers Part #: 66130
    Your Price: $22.56
    Head Handler Set 8mm x 1.25 This unique tool allows the technician to easily lift and maneuver cylinder heads when service is needed. First, free the cylinder head from the block then choose the appropriate thread size. Then used in tandem, simply spin the Head HandlerT into each end of the cylinder head until snug (use your descretion for strongest hold location). Now you can easily lift and carry the head. No more cut fingers from sharp edges ...
  • Installing Bar for 1201
    Installing Bar for 1201
    Manufacturers Part #: 41291
    Your Price: $415.91Includes Free Shipping
    Included in OTC 1201 Installing Conversion Kit and 1202 17-1/2 Ton Hydraulic Seeve Puller Set. OTC 41291 Installing Bar ...

Customers Also Purchased:

Customers Also Shopped For:

  • Axle Seal Installer
    Axle Seal Installer
    Manufacturers Part #: J-41102
    Your Price: $90.32
    Axle Seal Installer J-41102 Tool Number: J-41102 Tool Name: Axle Seal Installer 4T40E J/N J-41102 is a two piece plastic seal to install the axle shaft seals. The cone is designed to protect the rubber end of the sleeve during installation of the axle seal. Kent-Moore KM J-41102 Axle Seal Installer ...
  • Flex Wire Magnet
    Flex Wire Magnet
    Manufacturers Part #: 900WF
    Your Price: $7.64
    Features and Benefits: 19" flexible copper section 3 lb. lift 25" overall Perfect for reaching in small places Made in U.S.A. using US and Global Components Magnet has an overall length of 25". SE Tools 900WF Flex Wire Magnet SES900WF...
  • LG SEGMENT SET
    LG SEGMENT SET
    Manufacturers Part #: 34470
    Your Price: $21.36
    • For Exhaust/Tailpipe Stretcher (34400)...
  • Output Shaft Sleeve Remover 4T40E
    Output Shaft Sleeve Remover 4T40E
    Manufacturers Part #: J-41227
    Your Price: $217.50Includes Free Shipping
    Non-stock item; manufacturer drop ship please email service@toolsource.com for lead time. Applications: 4T40E 4T40E, 4T65E J-41227 is a two leg puller designed to locate behind the back lip of the sleeve for removal.This tool is required due to the limited access to the axle sleeve.The sleeve must be replaced when servicing the axle seals. Kent-Moore J-41227 Output Shaft Sleeve Remover ...
  • ProGauge II Paint Thickness Gauge
    ProGauge II Paint Thickness Gauge
    Manufacturers Part #: 2438
    Your Price: $55.30
    ProGauge II is a magnetic coating thickness gauge that measures the thickness of non-ferrous coatings on steel with a range of 1 to 15 mils or B model 0 to 350 microns. Know when panels are repainted; know when paint is too thick or thin. Easy to use: just place on paint, read scale as gauge is pulled off the paint. Used by car collectors & insurance adjusters. Includes heavy duty case and instruction book complete with information on automotive ...
  • Output Shaft Sleeve Installer 4T40E
    Output Shaft Sleeve Installer 4T40E
    Manufacturers Part #: J-41228
    Your Price: $253.92Includes Free Shipping
    4T40E J/N J 41228 is a five piece tool used to properly install the 4T40Eb axle sleeve. This tool grips the output shaft ring groove with four legs to insure proper sleeve alignment and installation while maintaining lateral run out of .001".Applications: 4T40E This item may not be in stock; please email service@toolsource.com for lead time. Kent-Moore J-41228 Output Shaft Sleeve Installer ...

Current Reviews: 0