TecMate TM-141 OptiMate 4 Diagnostic Battery Charger Optimizer TECTM-141

Home » Toolsource » Motorcycle Tools » Motorcycle Battery » 104213
OptiMate 4 Diagnostic Battery Charger Optimizer Toolsource #104213 Manufacturers Part Number #TM-141	$63.81

Click to enlarge

OptiMate 4: The new benchmark – A truly unique diagnostic battery optimizer for 12V lead-acid batteries (sealed maintenance-free, gel, or filler caps) up to 50Ah.

Like all OptiMate models before it, the microprocessor controlled OptiMate 4 can save neglected batteries, but the OptiMate 4 is even more effective, with a new dual-stage RECOVERY + TURBO RECOVERY desulfating action. For neglected deep-discharged batteries the RECOVERY mode engages automatically, while the TURBO RECOVERY mode engages for more severely neglected batteries.

**Like all other OptiMates, the OptiMate 4 then charges the battery, verifies that the battery is as fully charged as its basic state of health allows, and then checks for & detects dead battery cells.

Now OptiMate 4 also has the following new features :

Maximum output current increased to 0,8A without increasing energy consumption.
48 hour time limit on stages up to the first of the cyclic tests for battery drain to avoid wasting time and energy on batteries with a shorted-out cell.
19 possible LED indications displayed on 10 LEDs on the stunning new control panel.
5 possible results of the cyclic hourly tests for power drain /retention are displayed on a combination of green, yellow & red TEST LEDs.
IP64 weatherproof sealed enclosure with built-in mounting option (replaceable if damaged for example by over-tightening a fixing screw).
New cable bushings avoid insulation stress in ultra-cold temperatures.
New SAE weatherproof connections.

But, the most important attribute of the OptiMate 4, as with all OptiMates, is the safe, optimal maintenance of your battery during long term storage, achieved by its gentle maintenance cycle which automatically allows the battery to rest for 30 minutes of each hour of the maintenance cycle while it remains connected.

The automatic multi stage program engages as soon as the OptiMate is connected to a 12V battery that has at least 2V :

The OptiMate 4 immediately checks if the battery has enough voltage to start the program, and whether the battery is deep-discharged ("sulfated") or not.
For neglected batteries, the OptiMate 4 starts the recovery mode, initially limiting the applied voltage at 16V, and if necessary for sulfated batteries, engaging TURBO recovery at a voltage of up to 22V** at low current for up to 2 hours, to recover the battery to a condition in which it can accept a normal charge.
As soon as the circuit detects that this point has been reached (immediately for most batteries), the “bulk charge” mode engages and delivers current at a constant rate of 0,8A to charge the battery.
When the battery-sensing circuit observes that charge progress is sufficient, the unique ‘verification’ stage engages. The voltage is limited at a lower level, & if sensed necessary, a voltage pulsing action provides further desulfating & tops off the charge. When this has been verified, or if after 48 hours from connection the battery has been unable to accept & retain adequate charge, the next stage engages.
The OptiMate then stops current to the battery for 30 minutes while it monitors the unsupported battery voltage to check whether the battery can retain sufficient charge to crank an engine, before the long term maintenance and test cycle begins.
During the next 30 minutes the OptiMate offers the battery a supporting & maintaining charge, but only to the extent necessary to counter any losses or connected loads such as an electronic alarm or immobilizer. Overcharging and/or overheating of the battery is ruled out by this 50% duty cycle as the battery is interactively maintained for 30 minutes and then rests during the power drain tests of each alternative 30 minutes. So the battery is always 100% good to go, but never overcharged.

**The OptiMate’s high voltage desulfation mode cannot engage unless the battery is first disconnected from the vehicle’s electrical system. However, even if the battery is not disconnected, the OptiMate cannot damage sensitive vehicle electronics as the higher voltage mode can only engage if minimal or zero current is flowing into the battery.

Meets all relevant UL & CSA standards.
Comprehensive selection of SAE connection accessories including an output extension set.
2 year limited warranty
Note: The OptiMate 4 both has wall mounts included in the enclosure, so there is no need any longer to purchase a wall bracket.

TecMate TM-141 OptiMate 4 Diagnostic Battery Charger Optimizer

This product was added to our catalog on Thursday 16 October, 2008.

Optional Related Products

Replacement Gates Adapter for Optimate 3 @ $5.10	Compact Wall Bracket for Optimate 3 @ $8.19	TecMate Charger Wallbracket @ $9.79
Charge Cable Extender @ $5.92	Weatherproof Permanent Connector for Optimate 3 @ $6.13	DINSOCKET Optimate III, DIN Socket @ $13.13
Alligator / Battery Clips @ $7.16	Bike / Car 12V Cigarette Lighter Socket Connector @ $13.34

Customers who bought this item also purchased

125 Amp Heavy Duty Battery Tester, 6 or 12 Volt	Probulator - Electrical Back Probes	Motorcycle Brake Bleeder
Complete Cooling System & Cap Tester KDT3700	Belt Tension Gauge - Motorcycle	Brake Bleeding Kit MV8020

Toolsource

Search by Manufacturer

Search by Categories